• <nav id="aguug"><option id="aguug"></option></nav>
  • 上海彬倫閥門有限公司

    熱門搜索: 自由浮球式蒸汽疏水閥系列 汽水分離器系列 倒吊桶式蒸汽疏水閥系列 杠桿浮球式蒸汽疏水閥系列

    聯系我們contact us

    上海彬倫閥門有限公司(中美合資)

    地址:上海市靜安區江場三路238號(上海市北半島國際中心)

    全國熱線:400-021-9678
    電話:021-51036285                            
    傳真:021-51036385

    手機:13611652063

    郵箱:shblvalve@vip.163.com

    疏水閥的選型技巧

    來源:疏水閥  發布時間:2017-05-09

      疏水閥的選型技巧:
      1、倒吊桶疏水閥:
      作為所有工藝負荷和蒸汽主管線疏水閥的首選,即所有需要對蒸汽疏水的場合。
      2、浮球熱靜力疏水閥:
      用于工藝疏水,尤其是在控制負荷3.5公斤以下(50psig)的應用場合或空氣含量高、安裝倒吊桶疏水閥有問題的場合。
      3、平衡壓力疏水閥:
      用作不重要的伴熱或加熱系統。
      4、雙金屬片熱靜力疏水閥:
      用于伴熱管線或加熱系統低溫或防霜工況。該類型的疏水閥可以最大限度地利用凝結水中的顯熱或防止產品過熱。其閥體為全不銹鋼。
      5、熱動力圓盤疏水閥:
      只要在先前經驗證明其性能良好時,可作為倒吊桶疏水閥的替代產品,在壓力為17公斤以下的蒸汽主管和伴熱管上有限制地使用,或作為產品替換用于更高的蒸汽壓力。因其能源效率低,使用壽命短,不推薦使用(而且,在Huddersfield和Grangemouth工廠不允許使用)。
      6、在熱量要求不高的場合,用熱靜力疏水閥取代熱動力圓盤疏水閥會提高節能效果,同時保證使用壽命。
      7、機械疏水閥(即倒吊桶和浮球疏水閥)無論在凝結水負荷大或負荷小的情況下都可以保證蒸汽不含冷凝水,而熱靜力疏水閥在負荷增加的時候容易積聚凝結水。
      譯文:Trap selection techniques: An inverted bucket trap: As the process load and steam mains trap of choice for all those in need on the occasion of the steam trap. 2, the float thermostatic steam traps: Used to process the hydrophobic, especially in the application of the control load of less than 3.5 kg (50 psig) or high air content, install the inverted bucket trap occasions. 3, the balanced pressure steam trap: As unimportant heating or heating system. 4, bimetal thermostatic steam traps: For heating pipes or heating system, low temperature or frost prevention conditions. The types of traps can maximize the use of the sensible heat of condensation of water to prevent overheating. Its body made ??of stainless steel. 5, thermodynamic disc trap: Previous experience proved its good performance, can be used as alternative to inverted bucket trap at a pressure of 17 kg of steam mains, and with heat pipe, limited use, or as a replacement for the higher vapor pressure. Because of its low energy efficiency, life is short, not recommended (and in the Huddersfield and Grangemouth factory are not allowed). Less demanding situations, the heat, thermostatic steam traps to replace the thermodynamic disc trap will increase energy savings, life assurance. 7, mechanical traps (ie, inverted bucket and float trap) both in the case of condensation of the water load large or small load to ensure that the steam does not contain a condensate, while the thermostatic steam traps in the load increases the accumulation of condensation Trap selection techniques: An inverted bucket trap: As the process load and steam mains trap of choice for all those in need on the occasion of the steam trap. 2, the float thermostatic steam traps: Used to process the hydrophobic, especially in the application of the control load of less than 3.5 kg (50 psig) or high air content, install the inverted bucket trap occasions. 3, the balanced pressure steam trap: As unimportant heating or heating system. 4, bimetal thermostatic steam traps: For heating pipes or heating system, low temperature or frost prevention conditions. The types of traps can maximize the use of the sensible heat of condensation of water to prevent overheating. Its body made ??of stainless steel. 5, thermodynamic disc trap: Previous experience proved its good performance, can be used as alternative to inverted bucket trap at a pressure of 17 kg of steam mains, and with heat pipe, limited use, or as a replacement for the higher vapor pressure. Because of its low energy efficiency, life is short, not recommended (and in the Huddersfield and Grangemouth factory are not allowed). Less demanding situations, the heat, thermostatic steam traps to replace the thermodynamic disc trap will increase energy savings, life assurance. 7, mechanical traps (ie, inverted bucket and float trap) both in the case of condensation of the water load large or small load to ensure that the steam does not contain a condensate, while the thermostatic steam traps in the load increases the accumulation of condensation water.

    上一頁:倒吊桶式疏水閥在橡膠工業蒸汽硫化設備中的應用    下一頁:怎樣安裝疏水閥

    關于我們 | 企業資質 | 產品中心 | 新聞中心 | 在線訂單 | 聯系我們 |

    上海彬倫閥門有限公司(中美合資)滬ICP備20001747號-1
    電話:400-021-9678傳真: 021-51036385地址:上海市靜安區江場三路238號(上海市北半島國際中心)

    日本熟妇人妻VIDEOS